Mounting enforeComet with VESA stand

  • Updated

You want to set up your enforeComet and give your customers an overview over the order or the product selection with a customer display? Learn how to mount your enforeComet and customer display to the VESA stand in this How-To.

First check if all components are included in the delivery:

Bildschirmfoto_2021-09-01_um_14.29.23.png Bildschirmfoto_2021-09-01_um_14.30.07.png Bildschirmfoto_2021-09-01_um_14.30.37.png
enforeComet Customer Display VESA stand
1 x enforeComet 1 x 10.1" customer display 1 x holder enforeComet
1 x spacer 1 x power supply 1 x holder customer display
1 x power supply   1 x stand foot
1 x cold device plug   4 x M4 x 13 (crosshead)
    4 x M4 x 10 (crosshead)
    4 x M4 x 8 (crosshead)
    2 x M5 x 12 (hexagonal key)
    2 x cable tie
   

1 x HDMI cable

Bildschirmfoto_2021-09-01_um_14.35.33.png

Tools Needed

You will also need the following tools to assemble the VESA stand:

  • 1 x scissors 
  • 1 x crosshead screwdriver
  • 1 x hexagonal key 4 mm

Assembly

During assembly, use bubble wrap as a base to prevent damage to the devices.

  1. Remove the facing on the back of the holder for the customer display. 
    Bildschirmfoto_2021-08-30_um_13.41.24.png
  2. Loosen the screws on the back. 
    Bildschirmfoto_2021-08-30_um_13.42.08.png
    ⮕ You have successfully removed the facing from the holder.
    Bildschirmfoto_2021-09-01_um_14.38.43.png
  3. Now attach the lower two screws of the holder to the thread on the customer display.
  4. Screw the holder to the customer display using the M4 x 10 screws. 
    Bildschirmfoto_2021-08-30_um_13.43.52.png
    ⮕ You have successfully attached the holder to the customer display.
  5. Unfold the holder by 90 degrees.
  6. Screw the holder to the customer display at the previously hidden holes of the holder using the M4 x 10 screws. 
    Bildschirmfoto_2021-08-30_um_14.03.01.png Bildschirmfoto_2021-08-30_um_14.03.33.png
  7. Screw the spacer to the enforeComet using the M4 x 13 screws. 
  8. Screw the holder for the enforeComet to the enforeComet using the top two screws.
    Bildschirmfoto_2021-08-31_um_14.48.27.png
    ⮕ You have successfully attached the holder to the enforeComet.
    Bildschirmfoto_2021-09-01_um_15.05.47.png
  9. Unfold the holder on the enforeComet by 90 degrees.
  10. Screw the holder to the previously hidden holes of the holder using the M4 x 10 screws. 
    Bildschirmfoto_2021-08-31_um_14.51.31.png Bildschirmfoto_2021-08-31_um_14.52.14.png
    ⮕ You have successfully attached the holder to the enforeComet.
    Bildschirmfoto_2021-09-01_um_15.07.40.png
  11. Mount the holder connected to the customer display to the stand foot using the M5 x 12 screws.
    Bildschirmfoto_2021-09-01_um_10.04.58.png  Bildschirmfoto_2021-09-01_um_10.06.31.png
    ⮕ You have successfully connected the holder to the stand foot.
    Bildschirmfoto_2021-09-01_um_15.13.58.png
  12. Screw the stand foot on the back.
    Bildschirmfoto_2021-09-01_um_10.19.06.png
  13. Rotate the stand foot by 180 degrees so that the customer display is on the stand foot.
  14. Flip the customer display down by 90 degrees. 
    Bildschirmfoto_2021-09-01_um_10.19.34.png
  15. Screw the holder of the enforeComet to the holder of the customer display using four M4 x 8 screws. 
    Bildschirmfoto_2021-09-01_um_10.26.29.png
    ⮕ You have successfully attached the customer display and your enforeComet to the VESA stand.
    Bildschirmfoto_2021-09-01_um_10.29.47.png
  16. Connect the cash drawer cable to the enforeComet. To do this, pull the cable through the slit in the stand foot.
    Bildschirmfoto_2021-09-01_um_10.51.44.png Bildschirmfoto_2021-09-01_um_13.01.11.png
  17. Connect the power cable of the enforeComet and the cable of the USB printer to the enforeComet. To do this, pull the cables through the slit in the stand foot again.
    Bildschirmfoto_2021-09-01_um_13.14.12.png Bildschirmfoto_2021-09-01_um_13.14.50.png
  18. Connect the power cable for the customer display to the enforeComet. To do this, pull the cable through the slit in the stand foot again.
    Bildschirmfoto_2021-09-01_um_13.26.23.png Bildschirmfoto_2021-09-01_um_13.26.47.png
  19. Connect the HDMI cable to the enforeComet. To do this, pull the cable through the slit in the stand foot again.
    Bildschirmfoto_2021-09-01_um_13.47.20.png
    Bildschirmfoto_2021-09-01_um_13.47.51.png 
  20. Optionally, tie the cables together with cable ties and hide them in the stand so that the cables do not get in the way or interfere with work.
    Bildschirmfoto_2021-09-01_um_14.07.44.png Bildschirmfoto_2021-09-01_um_14.08.17.png
    ⮕ You have successfully connected the cables and tied them together with cable ties. 
    Bildschirmfoto_2021-09-01_um_14.11.16.png

Learn more...

Share this article

Was this article helpful?

0 out of 0 found this helpful

Have more questions? Submit a request